Modell KEM-CM21
|
The Kemo CardMaster 21.255G is a filter card designed for applications requiring occasional manual adjustment of cut-off frequency and gain. The CardMaster 255G can be fully controlled via the optional interface, using simple text based commands sent over Ethernet type hardware. Cut-off for each channel is set using two front panel hexadecimal rotary switches, and gain by two front panel switches. CardMaster 21.255G is a member of the Series 21 family of signal conditioning components and can be used in mixed systems comprising different cards from the Series 21 filters. Gain of 1, 2, 5, 10, 20, 50, 100, 200 and 500 is set by front panel switches. Input configuration is set by on board jumpers.
Up to 18 CardMaster 21.255G s can be fitted to the Kemo 21.18 rack, or 1 in the compact portable DC powered minirack. The CardMaster 21.255G is based on the Kemo 1600 Series filter module, to provide a filtering solution for applications where filter cut-off frequencies need to changed.
Frequency Range
The frequency range of a CardMaster 255G card is expressed in terms of its ‘base frequency’ ff; the card can be set to any frequency between ff and 255ff, in steps of ff. Cards can be ordered with base frequencies ranging from 1Hz to 500Hz on a 1/2/5 scale. We make the most appropriate combination from 1200 Series filter modules and controlling components. Frequency setting 255 is filter bypass.
Easy Control
The frequency and gain are set by front panel switches. Controls for IEPE, AC/DC input coupling, and single
Filter Responses
The CardMaster 255G can be fitted with the standard range of Kemo filter responses. These are:Butterworth 4 pole (05) and 8 pole (03),
Bessel 4 pole (09) and 8 pole (07),
Sharp anti-aliasing type, flat to filter cut-off (01),
General purpose, flat to cut-off, linear phase (41)
The CardMaster 255G can be fitted with almost any other filter response in the Kemo range of filter responses. The filter response is specified at order, any questions about which one, contact us and we are pleased to advise you.
Inputs and Gain
From our experience of signal filtering we have included a versatile set of input configurations and gain on the CardMaster 21.255G. Each channel can be independently configured.Inputs - AC or DC coupling, set by on board jumpers.
Input Mode - Single ended or differential, set by on board jumpers. Note:- AC coupling is on both inputs of differential input.
Transducer Power - current source for IEPE transducers, 24V 1-10 mA, set by user selectable resistor, factory set value, 4 mA.
Input Gain - set on front panel, two switches, x1,x2 (+6dB),x5 (+14dB) and x1,x10 (+20dB),x100 (+40dB), to give 1,2,5 steps to x500 (+54dB).
All the above settings can be controlled by the external Ethernet interface.
Trims - Gain and DC offset can be trimmed by multi-turn pots on the board.
Output attenuation - if required the output can be passively attenuated.
Signal Level Indication
CardMaster 21.255G cards have a signal level indication LED fitted between the input gain stages and the filter.Signal level indication - 0%- off -10% - green - 70% - orange - 95% - red.
Optional Signal Offset
CardMaster 21.255G cards are now fitted with additional offset on the single ended input, and on the output, up to +/- 5V offset can be applied to the signal making them suitable for use with 0-5V or similar unipolar data acquisition systems.
Special Connectors
The Kemo 21.18 rack and CardMaster 21.255G cards are designed for fitting special connectors. These can be fitted to the rear panel, or to a spare slot on the front. Typically we have fitted 25 way 'D' type connectors, with all the filtered outputs on one front panel connector. We have also fitted customer specific connectors to the rear panel. Let us know what you would like.
Optional External Control
CardMaster 21.255G cards are fitted with control logic compatible with the Kemo FICL II interface for external computer control. This is a text (ASCII) over a 10BaseT, RJ45 plug, Ethernet style hardware interface. This provides an operating system independent interface. the interface stores current data, verifies incoming commands, and then executes them. CardMaster 255G filter cards, like other Kemo units, are receive only on the rack control bus. More than one filter card can be set to the same address, they will all execute the same command. So one command can set a group of cards to the same settings. Simple text commands are used, the screen image shows typical commands sent via HyperTerminal.Typical response time to send commands to one channel and implement the settings is about 200mS. Typical response time to refresh all 64 channels is about 15 seconds.
The interface will accept text files, so complete set up information for multi-channel filter systems can be sent as one file. the RDBK files can be stored as text files, so test setups can be stored for measurement audit purposes.
DC Power
DC power, 9-30V DC input is available as an option for Kemo 21.18 racks, with an AC ‘power brick’ to power the unit from mains when available.
LED Indicators
The LED indicators on the CardMaster 255G can be turned off by on board jumpers.Specifications | |
---|---|
Performance | |
Channels | 1 channel per card, 1 slot in Kemo rack |
Control | Filter cut-off and
gain set by front panel switches.
Other parameters by on board jumpers or selectable components. Optional External control, 10BaseT text based FICL II interface. (19" rack only) |
Frequency | 254 cut-off steps, and filter bypass |
Gain | 1, 2, 5, 10, 20, 50, 100, 200, 500, (+54dB) with optional factory fitted output attenuation |
Filters | 1600 series filter modules |
Filter Responses | Defined by filter modules |
Input Coupling | AC / DC, Single ended / differential set by internal jumpers |
Input Overload | Absolute Input overload (single ended or differential) |
IEPE | 4mA 24V current source ( selectable 1-10mA ) |
Signal Level | ± 10 V pk-pk. (Usually with ‘headroom’) |
Signal Offsets | ± 50% on output, +/- 50% on output single ended only. Factory fitted option. |
Signal Level Indication | 3 colour, 4 signal level, off / green / yellow / red |
Size | 1 Series 21 slot (100x220mm Eurocard) |
Racks, Size and Weight | 21.18 Rack(19") - up to 18 channels, 420 x 155 x 350mm (16.6 x 6.1 x 13.8"), 10 kg, (22 lb) maximum. 21.1 Minirack - 1 channel, 44 x 116 x 270 mm (1.7 x 4.6 x 10.7") 1 kg ( 2.2 lb) maximum. |
Power | 21.18 rack 90 -120/180-240 Vac 50/60Hz
- Optional DC power 21.1 minirack 9 - 30V DC power |
Available Frequency Ranges | |
Frequency Range / Hz | Steps |
0.2 - 50.8 | 254 x 0.2 Hz |
1 - 254 | 254 x 1 Hz |
2 - 508 | 254 x 2 Hz |
5 - 1 270 | 254 x 5 Hz |
10 - 2 540 | 254 x 10 Hz |
20 - 5 080 | 254 x 20 Hz |
50 - 12 700 | 254 x 50 Hz |
100 - 25 400 | 254 x 100 Hz |
200 - 50 800 | 254 x 200 Hz |
500 - 127 000 | 254 x 500 Hz |