PCB Test & Measurement Seite 125

Hinweis: Dies ist eine maschinenlesbare No-Flash Ansicht.
Klicken Sie hier um zur Online-Version zu gelangen.

Inhalt

For Additional Specification Information Visit www pcb com PCB PIEZOTRONICS INC 716 684 0001 Fax 716 685 3886 123 Calibration Services Highlights Traceable to NIST and PTB laboratories Dynamic and static calibration capabilities Sensor performance evaluation testing ISO 9001 2000 certified ISO 17025 accredited by A2LA for most services The industry s most comprehensive capabilities PCB Piezotronics provides some of the most comprehensive calibration and testing services in the industry Considerable investment in equipment coupled with conformance to industry and ISO 9001 standards ensures that PCB sensors will perform in accordance with their specifications Calibration services are also available for other manufacturer s sensors A complete sensor calibration encompasses sensitivity linearity and where applicable its frequency response determination In addition evaluation of a sensor s performance for the various environments in which it will operate is desirable PCB provides all of these services Manufacturer PCB Sample Serial Number Joe CalibratorTechnician Per ISO 16063 21 08 06 10Date 9 6 10 0 Calibration Data Sensitivity Plot Data Points Output Bias VDC 0 2 15 0 0 0 30 0 0 1 0 0 REF FREQ 0 0 300 0 0 1 500 0 0 1 1000 0 0 2 3000 0 1 0 4000 0 4 0 Sensitivity 100 0 Hz mV g cal48 3363966737 87 Frequency Dev Frequency Dev dB 50 0 Hz Calibration Certificate ICP Accelerometer Description 353B33 Model Number Condition of Unit Notes n aAs Found 1 Calibration is NIST Traceable thru Project 822 277342 and PTB Traceable thru Project 1254 2 This certificate shall not be reproduced except in full without written approval from PCB Piezotronics Inc 3 Calibration is performed in compliance with ISO 9001 ISO 10012 1 ANSI NCSL Z540 1 1994 and ISO 17025 4 See Manufacturer s Specification Sheet for a detailed listing of performance specifications 5 Measurement uncertainty 95 confidence level with coverage factor of 2 for frequency ranges tested during calibration are as follows 5 9 Hz 2 0 10 99 Hz 1 5 100 1999 Hz 1 0 2 10 kHz 2 5 Hz Hz New Unit In ToleranceAs Left 1PAGE 1 of 3 0 3 0 2 0 1 0 0 0 1 0 2 0 4000 010 0 100 0 1000 0 101 7 3425 Walden Avenue Depew NY 14043 TEL 888 684 0013 FAX 716 685 3886 www pcb com 56Relative Humidity Temperature 73 F 23 C Mounting Surface Stainless Steel w Silicone Grease Coating Fastener Stud Mount 10 0 g 98 1 m s Acceleration Level rms Fixture Orientation Vertical 0 2Transverse Sensitivity 0 5Discharge Time Constant seconds 25 9 kHz 10 37 mV m s Resonant Frequency The acceleration level may be limited by shaker displacement at low frequencies If the listed level cannot be obtained the calibration system uses the following formula to set the vibration amplitude Acceleration Level g 0 010 x freq The gravitational constant used for calculations by the calibration system is 1 g 9 80665 m s CALIBRATION CERT 1862 01 Back to Back ComparisonMethod AT401 3 Typical Accelerometer Calibration Certificate For Shock Vibration Acoustic Pressure Force Torque Sensors and Load Cells 8 T Mcatalog 2011 Seite 109 124 SYN G500 21 04 11 18 01 Seite 129